A 300mm sliding table saw blade is a TCT circular blade with a 30 mm bore, a 3.2 mm kerf and a 2.2 mm plate, sized for 250–300 mm panel saws that spin at 4,000–5,000 rpm. Diameter sets rim speed and depth of cut; kerf and tooth count set what a 3 kW motor can pull without stalling. The rpm stamp overrides every table.

A 300 mm TCT body from the GUSHI Tools ripping range: laser-cut expansion slots, brazed tips, 30 mm bore.
What changes when a 300 mm blade goes on a sliding table saw?
Three numbers move at once. Rim speed rises 20 % at the same spindle speed, depth of cut rises about 25 mm, and spindle load rises with every extra millimetre of radius the motor has to accelerate.
Short answer: a 300 mm blade is a deep-cut blade, not a faster blade. European panel shops fit one for 40–100 mm work or when the saw carries a 120 mm scoring unit, and stay on 250 mm for 18 mm board and hand-fed ripping.
Rim speed is arithmetic: pi × diameter × rpm ÷ 60. A 300 mm blade at 5,000 rpm runs at 78.5 m/s, at 4,000 rpm it runs at 62.8 m/s, and a 250 mm blade at 6,000 rpm also lands at 78.5 m/s.
The 80 m/s line is the design basis most TCT makers work to, which is why a published blade size chart lists 6,100 rpm for 250 mm and 5,100 rpm for 300 mm (Compel, reviewed August 2026).
Depth of cut is why buyers ask for the larger blade. A 300 mm blade on a 3,200 mm sliding table saw exposes 100 mm above the table, and the same chassis with a 250 mm blade exposes roughly 75 mm. For 60 mm stiles or 80 mm glued beams, quote a table saw ripping blade for thick solid stock rather than the 250 mm line.
Which blade does a 3 kW motor actually pull?
Most 300 mm sliding table saws ship with a choice of main motor: 5.5 kW on three-phase supply, or 3 kW on single-phase for smaller workshops. The 3 kW option exists because a 230 V single-phase circuit cannot deliver much more. Spindle, arbor and blade capacity stay the same, so the blade gets chosen against the weaker motor.
Motor load tracks the volume of material removed per second. Kerf, depth of cut and feed speed multiply into that volume, so a change in any one moves the power draw in proportion. A 2.4 mm kerf removes 25 % less material than a 3.2 mm kerf at equal depth and feed.
| Change on a 3 kW saw | Effect on load | Practical note |
|---|---|---|
| Kerf 3.2 to 2.4 mm | About −25 % chip volume | Re-check the riving knife on thinner plate |
| Depth 40 to 80 mm | About +100 % | Two 40 mm passes beat one stalled pass |
| Feed 5 to 10 m/min | About +100 % | Hand feed is the variable you control |
| 40T to 96T, equal kerf | Slightly higher | Thin chips cost more energy per cm³ |
| Pine to MDF or HDF | Higher at equal volume | Resin and glue also blunt the edge sooner |
A 3 kW single-phase machine pulls a 300 mm blade through 18–25 mm MDF or chipboard at 3.2 mm kerf and hand feed. The same machine struggles on a 60 mm beech rip, where 5.5 kW three-phase is the honest answer. If the motor trips mid-cut on thick hardwood, fit a 250 mm blade before buying a bigger motor: the smaller blade restores 20–30 % of the power margin and costs 25 mm of depth.
How do 250 mm and 300 mm blades compare on paper?
The table below is the sheet we send when a distributor wants a 300mm sliding table saw blade beside a 250 mm rip cut table saw blade with a 30 mm bore in one catalogue. The rpm column is the 80 m/s basis, not a product rating.
| Diameter | Teeth / grind | Kerf | Plate | Bore | Hook | Rpm at 80 m/s | Job |
|---|---|---|---|---|---|---|---|
| 250 mm | 40T ATB | 3.2 mm | 2.2 mm | 30 mm | 15–20° | 6,100 | Rip, 20–75 mm |
| 250 mm | 80T TCG | 3.2 mm | 2.2 mm | 30 mm | 5–10° | 6,100 | Coated panel |
| 300 mm | 40T ATB | 3.0 mm | 2.2 mm | 30 mm | 15–20° | 5,100 | Deep rip, 75–100 mm |
| 300 mm | 72–84T TCG | 3.2 mm | 2.2 mm | 30 mm | 10° | 5,100 | Sizing, laminate |
| 300 mm | 96T TCG | 3.2 mm | 2.2 mm | 30 mm | −3° | 5,100 | Fine panel, no scoring |
Two rows deserve a comment.
40T rip at 3.0 mm kerf: 100 mm of cut height already loads a 3 kW motor, and 0.2 mm of kerf is free power.
96T TCG at −3° hook: negative rake pulls the panel onto the table and holds the melamine face still as the tooth exits.

A 300 mm TCG panel blade with the scoring blade it pairs with on a sliding table saw.
What does the EN 847-1 marking tell you before you quote?
EN 847-1 is the European tool-safety standard for woodworking cutters and saw blades. For a buyer, the useful part is the marking requirement: every blade carries its maximum rpm next to the rotation direction, so a blade can be checked against a machine without trusting a catalogue.
Read the stamp in this order and you have the line item:
Diameter × kerf / plate × bore, written as 300 × 3.2 / 2.2 × 30 mm.
Tooth count and code, for example Z96 for 96 teeth.
Maximum spindle speed, usually written n MAX 6500 RPM.
Rotation arrow, which must agree with the machine arrow.
Manufacturer mark, so a customs or GS auditor can trace the body.
Pinhole pattern on panel blades, for example 2/7/42 and 2/9/46.4.
Here is the point most blade charts miss. The 80 m/s table gives 5,100 rpm for a 300 mm blade, yet a 300 mm 96T body from the GUSHI Tools line is stamped n MAX 6500 RPM. Both numbers are correct: one is a generic design basis, the other is the declared rating of that body. The stamp governs, and EN 847-1 is built around the stamp.
Scope matters too. CE marking sits on the saw, because the saw is machinery under Regulation (EU) 2023/1230. A blade is a tool, covered by the declaration and data sheet tied to EN 847-1, with the EN 1870 series on the machine side. A distributor asking a blade supplier for a CE certificate for the blade is asking for the wrong document.
Where does a 300 mm blade lose accuracy on a 3 kW machine?
Deflection. A 300 mm body with a 2.2 mm plate has more unsupported diameter than a 250 mm body of the same plate, and hand feed on a sliding carriage pushes sideways as well as forward. Push that plate at 10 m/min through 60 mm oak and the rim leans into the cut.
The riving knife is the next failure point. It has to sit between plate and kerf, so a 3.2 mm kerf on a 2.2 mm plate leaves 0.5 mm of clearance each side. Swap to a 2.4 mm thin kerf without touching the knife and it is now wider than the cut on one side. If you change kerf, measure the knife before the first cut.
Scoring alignment decides the bottom edge. A 120 mm scoring table saw blade matched to the main kerf runs at 7,000 rpm on the same kerf line as the 300 mm blade. An adjustable scoring saw blade for coated panels removes the shimming step that most shops get wrong.
Arbor fit is the quiet one. European machines use a 30 mm spindle, smaller machines 20 mm, and a reduction ring lets a 30 mm bore sit on a 25.4 mm arbor. The ring never works the other way round, and forcing it puts runout into every cut.

Stamped body: 300 × 3.2 / 2.2 × 30 mm, 96 teeth, n MAX 6500 RPM. The stamp, not the chart, is the rating.
Which symptoms point to the blade rather than the machine?
Four symptoms cover most of the calls we get from European distributors, and three of them are blade or setup problems rather than machine faults. The guarding and kickback checks behind them are the ones the UK HSE woodworking guidance puts in front of every shop floor.
| Symptom | Likely cause | Change first |
|---|---|---|
| Burn marks, blue tips | Too many teeth or too slow a feed | 96T to 48T on solid wood, keep feeding |
| Chipped melamine underside | No scoring cut or scoring off the kerf line | Fit and align the 120 mm scoring blade |
| Cut wanders off the line | Plate deflection from feed force | Halve the feed, check flange, use 2.5 mm plate |
| Motor stalls at start | Deep cut plus fine pitch on single phase | 250 mm blade, thinner kerf, two passes |
A dull blade behaves differently again: the sound flattens, feed force climbs, and the cut stays straight. Dull blades get resharpened, mis-specified blades get replaced, and the second mistake is the cheaper one to avoid at the ordering stage.
How do you specify a 300 mm blade for a European distributor?
Seven answers turn into a quote without a follow-up email. German distributors index the line as Längsschnitt-Sägeblatt, Italian ones as lama per taglio longitudinale, and both check the same seven points against their machine list.
Diameter and bore, with the pinhole pattern if the machine has drive pins.
Kerf and plate quoted separately, because the riving knife sits between them.
Tooth count and grind: ATB for solid wood, TCG for panel sizing saw blades on a sliding table saw.
Hook angle: positive for hand feed, negative for coated panels and climb-cut risk.
Stamped maximum rpm, which has to sit above the machine speed at every setting.
Body steel and tip grade, if the distributor publishes a data sheet per item.
Packaging, label language and ISPM 15 heat-treated pallets for the EU delivery.
Shops that finish on an edge bander usually add a trimming saw blade for edge-banding work to the same order, because the trimming unit takes a different tooth geometry from the sizing line.
On the supply side, a 300mm sliding table saw blade order from GUSHI Tools runs through 15 or more cooperative factories with AQL 2.5 inspection and a batch number kept against a retained sample. Samples go out before a bulk order, because the customer's own machine is the only test that settles a hook-angle argument.
Frequently asked questions
Can I run a 300 mm blade on a saw built for 250 mm?
Only if three things check out. The guard and riving knife must clear the larger diameter, the spindle speed must stay below the stamped maximum of the new blade, and the table insert must not be cut through. A saw designed around 250 mm usually has a guard sized for it, so the answer is often no even when the arbor fits.
Is a 300 mm blade better than a 250 mm blade on a 3 kW motor?
No, and that is the trade. The larger blade adds about 25 mm of depth and asks more of the same motor at the same feed. A 250 mm blade cuts faster in 18–40 mm material; a 300 mm blade earns its place above 75 mm.
What bore does a European sliding table saw use?
30 mm is standard on 250 mm and 300 mm machines, with 20 mm on smaller saws. A reduction ring lets a 30 mm bore run on a 25.4 mm or 20 mm arbor, never the reverse. Order the bore against the machine list, because drive pins differ.
What kerf should I order for 18 mm MDF?
3.2 mm kerf is normal on a sliding table saw, paired with a 72T to 96T TCG blade. A 2.4 mm thin kerf cuts motor load by about a quarter, which matters on 3 kW single phase, but the riving knife then has to be checked against the thinner plate.
How many teeth does a 300 mm blade need for melamine?
72 to 96 teeth in TCG grind, used with a scoring blade on double-face laminate. TCG puts a flat raker between the chamfered teeth, so the exit edge of the melamine face is supported rather than lifted. Single-face board runs ATB at 60 to 72 teeth with less load.
What does n MAX 6500 RPM mean on a blade?
The figure is the highest spindle speed the blade is rated to run, marked under EN 847-1 next to the rotation arrow. Machine no-load speed must stay below it at every setting the saw offers. A 300 mm blade stamped 6500 rpm runs safely on a 4,000 or 5,000 rpm sliding table saw.

